臺灣博碩士論文加值系統

近幾年空間技術發展已趨近完整。在雷射掃描技術、航空與地面攝影測量技術，已經可以短時間內獲取高精度之三維資訊。台灣長期受到地震、豪雨、颱風等影響，自然因素發生頻繁，所以常造成災害發生，當災害發生，邊坡、土石狀況極為不穩定，本研究以木柵貓空纜車站指南宮站後方之猴山岳做為研究區域，期望以快速且動用最少人力、物力及考量測量人員安全因素之測量方法，快速紀錄災後現場的三維空間資訊，並建立可供展示及量測之三維模型，即時反映災害現場情況，可提供日後的研究與分析。
本研究將介紹以無人工佈標之近景攝影測量方法，以全測站量測獲取邊坡上特徵點坐標，應用軟體完成災害邊坡模型重建。為了評估研究中近景攝影測量重建之邊坡模型精度，精度檢核分成兩個部分：單點量測精度與模型精度。以全測站測得之控制點坐標，從中挑選出5點由控制點改為檢核點不解算外方位，求出全測站與立體量測各方向之殘差；模型精度檢核，研究使用高精度地面光達量測(Ground LiDAR)生成之模型作為檢測標準，比較兩個模型之間的差異。實驗最後以虛擬實境模組語言（Virtual Reality Modeling Language；VRML)展示成果。

Spatial technology has undergone rapid development in recent years. In laser scanning technology as well as aerial and terrestrial photogrammetry, highly accurate three-dimensional data can now be acquired in relatively short time. Taiwan is a place prone to calamities such as earthquakes, heavy rainfall and typhoons, which in turn result in highly unstable slope conditions and landslides. This study targets the area of Houshanyue behind Zhinan Temple Station of the Moakong Gondola in Muzha as a site of interest. Our purpose is to develop measurement methods which require minimal manpower and resources and in the meantime ensure personnel safety; this can facilitate instant documentation of three-dimensional data at disaster sites. Three-dimensional models constructed from such data can in turn be utilized for display and measurement purposes, providing immediate information from the sites of disaster and also material for subsequent study and analysis.
This study introduces a close-range photogrammetry method without artificial targets. We acquired feature point coordinates via total station measurement and performed software-assisted model reconstruction of slopes at disaster sites. To evaluate the accuracy of slope models, accuracy verification was focused on two aspects: single-point measurement accuracy and model accuracy. For the first aspect, among the control point coordinates obtained from the total station, five control points were selected and altered to checkpoints of non-solving exterior orientation, and the residuals on the model and between checkpoints were thus calculated. As for model accuracy verification, models generated via high accuracy ground LiDAR measurement served as standards for comparison of two different models. Final results were displayed in the form of Virtual Reality Modeling Language (VRML).
 

目錄
摘要 i
英文摘要 ii
誌謝 iv
目錄 v
表目錄 vii
圖目錄 viii
第一章 緒論 1
1.1 研究動機與目的 1
1.2 文獻回顧 4
1.3 研究架構 7
第二章 數值地形模型快速建置方案 10
2.1近景攝影測量 10
2.2 地面光達 24
第三章 無佈標之近景攝影測量試驗 29
3.1 研究區域 29
3.2 實驗儀器設備 34
3.3邊坡數值地形模型建置流程 38
3.3.1 現地測量 39
3.3.2邊坡數值地形模型建置 43
第四章 猴山岳實驗案例成果分析 54
4.1 精度檢核 54
4.2 根面積比(RAR)量測方法比較 62
第五章 結論與建議 70
參考文獻 72

[1] Abernethy, B. and Rutherfurd, I.D.（2001）. “The Distribution and Strength of Riparian Tree Roots in Relation to Riverbank Reinforcement”, Hydrological Process, Volume15, pp63-79.
[2] A. Bauer , G. Paar ,V. Kaufmann（2003）. “Terrestrial laser scanning for rock glacier monitoring” , Permafrost , Phillips , Springman & Arenson (eds) , Swets & Zeitlinger , Lisse ,ISBN 90 58095827 , pp.55-60 .
[3] Alshawabkeh Y. , Haala N. ,（2004）.“Intergration of digital photogrammetry and laser scanning for heritage documentation”. ISPRS Kongress 35, Part B, Istanbul, Turkey, digital on CD, 6pages.
[4] A.F. Habib, M.S. Ghanma, R.I., Al-Ruzouq, and E.M. Kim, (2004) . “3-D Modelling of Historical Sites Using Low-Cost Digital Camera”, SS4 – CIPA - Low-Cost Systems in Recording and Managing the Cultural Heritage.
http://www.isprs.org/proceedings/XXXV/congress/comm5/papers/618.pdf
[5] Alberto Guarnieri, Antonio Vettore, Fabio Remondino,（2004）. “Photogrammetry and Ground-based Laser Scanning: Assessment of MetricAccuracy of the 3D Model of Pozzoveggiani Church”,Athens, Greece, May 22-27.
http://www.photogrammetry.ethz.ch/general/persons/fabio/fig_atene.pdf
[6] Bauer A. , Paar G. , Kaufmann V.（2003）. “Terrestrial laser scanning for rock glacier monitoring”. In：Proceedings of the 8th Int. Conf. on Permafrost, Zurich, Vol. l, A.A. Balkema Publishers, pp55-60.
[7] Blais, F. ,（2004）.“Review of 20 years of range sensor development” , Journal of Electronic Imaging,13(1): 231–243.
[8] Bambang Kun Cahyono, Abdul Nasir Matori（2009）. “LANDSLIDE DETECTION ON SLOPE AREA BY USING CLOSE-RANGE PHOTOGRAMMETRIC DATA” , Prosiding Seminar Nasional Revitalisasi Data dan , Sains-Teknik, Prosiding Seminar / Lokakarya / Konferensi.
http://lib.ugm.ac.id/digitasi/index.php?module=cari_hasil_full&idbuku=915
[9] Chris Hopkinson, Laura Chasmer ,Colin Young-Pow ,Paul Treit（2004）. “Assessing forest metrics with a ground-based scanning lidar” ,Can. J. For. Res. Vol. 34 ,p573-583.
[10] Corsini, A., Borgatti, L., Cervi, F., Dahne, A., Ronchetti, F., Sterzai, P. （2009）.“Estimating mass-wasting processes in active earth slides - Earth flows with time-series of High-Resolution DEMs from photogrammetry and airborne LiDAR”, Natural Hazards and Earth System Science 9 (2), pp. 433-439.
[11] Danjon, F., Barker, D.H., Drexhage, M., Stoke, A.（2008）. “Using three-Dimensional Plant Root Architecture in Models of shallow-Slope stability .”Ann. Bot. Vol.101, No.8, pp.1281-1293.
[12] Edward M. Mikhail, James S. Bethel, and J. Chris McGlone (2001) . “Introduction to Modern Photogrammetry,”John Wiley & Sons, INC., New York, pp.247-275.
[13] El-Hakim, S. F., Beraldin, J. A., Gonzo, L., Whiting, E., Jemtrud, M., Valzano V.,（2005）.“A hierarchical 3D reconstruction approach for documenting complex heritage sites.”The CIPA 2005 International Symposium Torino, Italy.
http://www.3dphotomodeling.org/CIPA05.pdf
[14] Fabio Remondino, Sabry El-Hakim（2006）. “Image-based 3D modelling：a
review” ,The Photogrammetric Record, 21(115) , September, pp. 269-291.
[15] Gray, D.H., Leiser, A.T.,（1982）. “Biotechnical Slope Protection and Erosion Control”Van Nostrand Reinhold Company , New York, NY.
[16] Grün A. ,（2000）. “Semi-automated approaches to site recording anmodeling” , IAPRS&SIS, 33(5/1): 309-318.
[17] Halim Setan and Mohd Sharuddin Ibrahim(2004) . “Close Range Measurement and 3D Modeling”,1st FIG International Symposium on Engineering Surveys for Construction Works and Structural Engineering at Nottingham, United Kingdom, 28 June-1 Session 11.
http://www.fig.net/nottingham/proc/ts_11_3_setan_sharuddin.pdf
[18] Jana Visnovcova, Li Zhang, Armin Gruen（2001）. “Generating a 3D model of a Bayon tower using non-metric imagery”, IAPRS, 34(5/W1):30-39, Ayutthaya,Thailand, on CD-ROM.
[19] Johan Kasperski,Christophe Delacourt, Pascal Allemand , Pierre Pothe（2010）.“Evolution of the Sedrun landslide (Graubünden, Switzerland) with ortho-rectified air images , Springer-Verlag”, Bull Eng Geol Environ69:421–430.
[20] Karara, H. M., Abdel-Aziz, Y. I.（1974）. “Accuracy aspects of non-metric imageries”. Photogrammetric Engineering and Remote Sensing 52.
[21] Klaus Hanke, Mostafa Abdel-Bary Ebrahim, M.Sc.（1997）. “A Low Cost 3D Measurement Tool for Architectural and Archaeological Applications”, Goteborg Literature, Institute of Geodesy,University of Innsbruck, Austria. http://www.uibk.ac.at/vermessung/zeugs/lit-kh/goeteborg1-1997.pdf
[22] Kwan Lam Chow(2007) . Engineering Survey Applications of Terrestrial Laser Scannerin Highways Department of the Governmentof Hong Kong Special Administration Region (HKSAR) , Strategic Integration of Surveying Services, FIG Working Week 2007, Hong Kong SAR, China.
[23] Kasai M., Ikeda M., Asahina T., Fujisawa K.（2009）.“LiDAR-derived DEM evaluation of deep-seated landslides in a steep and rocky region of Japan”,Geomorphology Volume 113, Issue 1-2, 1 December 2009, P 57-69.
[24] Liebowitz, D., Criminisi, A. and Zisserman, A., （1999）.“Creating architectural models from images”. Computer Graphics Forum, 18(3): 39–50.
[25] Maher M. and Gray D.H.（1990）. “Static Response of Sands Reinforced with Randomly Distributed Fibers”, Journal of Geotechnical Engineering,Volume116,No.11 pp1661-1667.
[26] M. Yakar（2011）. “Using close range photogrammetry to measure the position of inaccessible geological features” ,experimental techniques,p54-59.
[27] Piegl，L，Tiller，W，（1997）. “The NURBS Book 2nd Edition ”,Springer Verlag.
[28] Park H（2001）. “Choosing nodes and knots in closed B-spline curve interpolation to point data”，Computer-Aided Design，Vol.33 NO.13，PP967-974.
[29] P. Baldi, N. Cenni, M. Fabris, A. Zanutta（2008）.“Kinematics of a landslide derived from archival photogrammetry and GPS data ” Volume 102, Issues 3-4, 15 December 2008, Pages 435-444.
[30] Ruinian Jiang, David V. Jauregui（2010）. “Development of a digital close-range photogrammetric bridge deflection measurement system” , Measurement Volume 43,lssue 10,Pages1431-1438.
[31] R. Kenner,M. Phillips,C. Denier,P. Thee,A. Zgraggen（2010）. “Investigation of rock and ice loss in a recently deglaciated mountain rock wall using terrestrial laser scanning：Gemsstock, Swiss Alps , Cold Regions Science and Technology ,Volume67 , lssue 3 , Pages157-164.
[32] Sabry F.El-Hakim（2002）. “Semi-automatic 3D reconstruction of occluded and unmarked surfaces from widely separated views” ，ISPRS Comm. V Symposium, Corfu, Greece, pp. 143-148, Sept. 2-6.
[33] Strozzi, T.Delaloye, R., Kääb, A. , Ambrosi, C. , Perruchoud, E. , Wegmüller, U.（2010）.“Combined observations of rock mass movements using satellite SAR interferometry, differential GPS, airborne digital photogrammetry, and airborne photography interpretation”, Journal of Geophysical Research,Volume 115 Issue 1, January 2010.
[34] Talend D.（2009）. “Robotic station reduces survey risks” ， Volume 210， Issue 10， December， Pages 80-81.
[35] USDA Soil Conservation Service（1978）. “Peredicting Rainfall Erosion Losses：a Guide to Conservation Planning”，USDA Agricultural Handbook＃537，Washington ，DC.
[36] V. Gischig , F. Amann , J.R. Moore , S. Loew , H. Eisenbeiss , W. Stempfhuber , （2011）. “Composite rock slope kinematics at the current Randa instability, Switzerland ,based on remote sensing and numerical modeling”, Engineering Geology,Engineering Geology 118 (2011) 37–53.
[37] Wu, T.H. ，Mckinnell，W.P. ，Swanston，D.N.（1979）. “Strength of Tree Roots and Landslides on Prince of Wales Island”，Alaska，Canadian Geotechnical Journal，Vol.16，No.1 pp.19-33.
[38] Waldron ,L.J.,Dakessian ,S.（1981）. “Soil Reinforcement by Roots：Calculation of Increased Soil Shear Resistance from Root Properties” Soil Science ,Vol.132,No.6,pp427-435.


[39] 王正忠（2002），以近景攝影測量進行模型式建物重建，碩士論文，國立成功大學測量工程學系。
[40] 石佑偉（2010），以物空間匹配方法重建三維顏面模型，碩士論文，國立臺北科技大學土木與防災所。
[41] 吳笛豪（2008），應用近景攝影測量與地面雷射掃描於的物量測精度及三維建模之研究，碩士論文，國立高雄應用科技大學土木工程與防災科技研究所。
[42] 吳明陽（2008），應用全測站經緯儀與近景攝影測量技術於地滑災害地形測量之可行性研究，碩士論文，國立中興大學土木工程學系。
[43] 何維信（2006），航空攝影測量學，大中國圖書公司。
[44] 林又青（2003），生態工法於坡趾穩定之初步分析及應用，碩士論文，國立台灣大學土木工程學研究所。
[45] 林卓群（2006），Lidar高精度數值地形應用於崩塌地區快速調查研究，碩士論文，國立成功大學資源工程學系。
[46] 林銘郎（2008），從政大御花園社區東側邊坡滑動災害暨貓纜塔基案例談都會周圍坡地開會與災害，貓空纜車塔柱沿線－地質環境問題研討會。
http://www.geotech.org.tw/
[47] 馬國宸（2008），土壤水分移動與植生根系對邊坡穩定之研究，博士論文，國立台灣大學生物環境系統工程學研究所。
[48] 孫浩淳（2010），採用根系纖維叢分析法的網路邊坡穩定程式開發，碩士論文，國立臺北科技大學土木與防災所。
[49] 許海龍、王偉群、陳立邦（2006），應用3D雷射掃描技術於崩塌地地層滑動監測，岩盤工程研討會論文集，June26-27，p377-386。
[50] 陳彥璋、陳偉堯譯（2005），坡地生態工法－坡地植生工程理論與實務，明文書局。原著：Gray D.H.and Sotir R.B.（1996）, Biotechnical and Soil Bioengimeering Slope Stabilization-A Practical Guide for Erosion Control, John Wiley and Sons, Inc。
[51] 陳秀婷（2006），植生土壤剪力強度之實驗量測與數值分析，碩士論文，國立中央大學土木工程研究所。
[52] 陳威丞（2008），應用近景攝影測量重塑顏面模型精度之評估，碩士論文，國立臺北科技大學土木防災研究所。
[53] 梁福榮（2006），攝影測量應用於古蹟紀錄和邊坡表面變化量量測之研究，碩士論文，國立成功大學土木工程學系。
[54] 梁福榮、張舜孔、李德河（2006），攝影測量於評估公路崩塌量量測之應用，岩盤工程研討會論文集pp347-356。
[55] 黃偉哲（2010)，近景攝影測量量測地形樣貌與山坡地崩塌量之研究－以苗栗火炎山為例，碩士論文，國立聯合大學土木與防災工程學系。
[56] 詹皇祥（2001），近景數化影像半自動式混凝土裂縫量測，碩士論文，國立中央大學土木工程研究所。
[57] 趙鍵哲、鄭傑文、陳詹閔、王匯智、林義乾、莊子毅、鄭傑中、彭念豪（2009），航空測量學講義，中華民國地籍測量學會專業訓練課程。
[58] 賴志凱（2004），地面雷射掃描儀的精度分析與檢定，碩士論文，國立成功大學測量及空間資訊學系。
[59] 蕭國鑫、劉進金、曾義星、王晉倫（2010），三維雷射掃描應用於崩塌土石量化之研究，航測及遙測學刊第十五卷第1期第97-109頁。
[60] canon規格手冊
[61] Riegl技術規範手冊